Controller priority?

[Sokol1]

The "old" il-2 limite controllers (josytick, throttle, pedal, button box...) to FOUR devices.

il-2:CloD dont have this limitation (probable it's same of Direct X: 16 controllers).

However, all controllers (josytick, throttle, pedal, button box...) have a unique ID number in this firmware, that dictates the order in which the Windows sees them.

Example: pluged to USB ports
Mjoy8 DIY (9 axis...) - firmware ID 0x002
Thrustmaster T.16000M - firmware ID 0xB10A
CH Fighterstick USB - firmware ID 0xC0F3

You can see this numbers with DXdiag, Imput tab.

EDIT - Or use VKB "ShowHID": http://www.vkb-pro.ru/downloads/prog...mmy/5-show-hid

How windows enumerate them:



How il-2:CloD enumerate them:



Joystick 0 in fact only Joystick = Mjoy (9 axis...)
Joystick 1 = Thrustaster T.16000M
Joystick 2 + CH Fighterstick USB

Notice that I have set X axis of each 3 stick in CloD GUI respectively for

Aileron = Joystick2 - CH Fighterstick USB
Elevator = Josytick 1 - Thrustaster T.16000M
Rudder - Mjoy (9 axis...)

Logitech provide a software - that work with another brands - caled JoyID that promises alter this enumeration. This DONT work for il-2:1946, I dont know if work in il-2:Clod (or Win7/8 64 bec ause are old), if you want a try:

http://www.wingmanteam.com/latest_so...oyIDs_Utility:

Related topic: http://forum.1cpublishing.eu/showthread.php?t=27113

Ok, and because you cant define your 3D stick in CLoD GUI for aileron, elevator, rudder, trhottle?

Probable because your BRD or Fanantec device is "jittering" and the CloD register the movemente in his pots signal before your joystick.
If you try and try, and try... perhaps you get 3D stick register before them.

In the above example the T.16000M rudder axis (RX) are jittering and sometimes are registered by GUI before move the intended controller.

Another way, unplug BRD and Fanatec, set the 3D stick, an test in game if are all OK.
If yes, plug BRD and Fanatec again, and DONT go to Control >Axis in CloD GUI more.

Now il-2:CloD dont see you 3d Stick again because Windows change your number (0 for 2 or 3) due presence of BRD and Fanatec.

No problem, open the file confUser.ini (...:\Documentos\1C SoftClub\il-2 sturmovik cliffs of dover (or - MOD)\), look for:

[HotKey pilotMove]
Joystick+AXE_RZ=1rudder
Joystick+AXE_Y=1elevator
Joystick+AXE_X=1aileron
Joystick+AXE_U=-1throttle

Change to

Joystick2+AXE_RZ=1rudder
Joystick2+AXE_Y=1elevator
Joystick2+AXE_X=1aileron
Joystick2+AXE_U=-1throttle

The above example assume the 3D joystick are the third device for Windows (check in Windows Control Panel -Printer and peripherals- or in DXdiag), if are the second use "Joystick1+AXE_RZ=1rudder... etc.

This 1 and -1 means if axis are reverse or no.

Buy a new stick dont overcome this, unless you know if his firmware number are lower that BRD and FAnatec.



Sokol1

[MarkJ]

Thanks for the lengthy detailed Reply Sokol1. I think you hit the nail on the head about another controller has a tiny jitter, enough to instantly register in CoD perhaps, as i know my pedals have a habit of doing that.
I will try some of your recommendations. I also found an older post that suggested manually editing the confuser.ini file to use the required controller and then 'loading' that in game, so will try that also once i have detected what controller ID is assigned to my stick.

[MarkJ]

Pleased to say I got this sorted last night. In the end I fired up rise of flight then opened il2 cod and by multiple inputs of the stick in each required axes I managed to config each for my wingman extreme. I then saved the profile.

Just need to assign a million other buttons now for all the other stuff!